AG132 A/C RECHARGE INSTRUCTIONS

Premium R-1234yf Recharge Kit with Digital Gauge & Smart Clips

AC AVALANCHE® is the smart way to recharge with both Temperature & Pressure to ensure maximum cold air. This kit contains:

  • Premium R-1234yf gas for maximum cold air.
  • #1 Super Chill Formula® pag oil that extends compressor life and rejuvenates seals, o-rings, gaskets, and hoses to prevent system leakage.
  • Easy-to-Read Digital PSI Pressure Gauge.
  • SMART CLIPS®, patented color-changing indicators, that signal interior vent temperature.
    ____ Blue = cool;    ____ Green = max cold
  • Flexible Recharge Hose with quick-connect coupler for easy low-side port connection.

INSTRUCTIONS:

CAUTION: ALWAYS WEAR PROTECTIVE RUBBER GLOVES AND EYE WEAR. DANGER: NEVER PLACE REFRIGERANT CAN ON ANY HOT ENGINE PART.

1. Remove SMART CLIPS from the cap and insert into vehicle’s center air vent.

  • Tighten recharge hose to can by turning counter-clockwise.
  • Activate digital gauge battery by removing clear tab.

2. Open vehicle hood, locate the low-side service port and remove port cap.

  • Recharge hose will only connect to the low-side port.

3. Start the engine and turn on A/C.

  • Set controls to maximum cool, maximum air flow and recirculation mode.
  • Close all windows and doors of vehicle.
  • Important: Let the A/C system run for several minutes to reach its maximum cooling capability.

4. Shake the can well and connect recharge hose to low-side service port.

  • Pull coupler ring back as you push fitting onto the port.
  • Ensure coupler locks in place to prevent leaking.

5. Determine the ideal PSI level using temperature pressure chart and check system pressure.

  • Read gauge pressure when the compressor clutch cycles on
  • If the gauge reads:
    • Below 25 PSI: system is low on refrigerant. Begin recharging process.
    • 25-55 PSI: system may be properly charged. Check SMART CLIPS, blue coloring indicates cool air is flowing.
    • Above 55 PSI: If compressor clutch is cycled on, do not recharge – seek a mechanic’s assistance.

6. Add refrigerant to the system.

  • Turn push-button on top of can to the unlock position.
  • Push button down while continually rotating the can in a sweeping motion from the 12 o’clock to 3 o’clock position.

7. Check gauge pressure every 10-15 seconds by releasing the push button.

  • Continue process until the gauge reaches the ideal PSI level according to the chart.
  • If your gauge is not increasing, stop charging and check SMART CLIPS as directed in next step.
  • DO NOT OVERCHARGE. DO NOT VENT.

8. Check SMART CLIPS for temperature.

  • With vehicle in park, press gas pedal slightly to increase RPM and check color for.
  • Blue = cool, approaching optimum fill.
  • Green = max cold, charging is complete.
  • NOTE: If outside temperature is above 95º, only the blue clip needs to change.

9. Stop charging when correct PSI level is reached or SMART CLIPS indicate the A/C is blowing cold.

  • Remove the quick-connect coupler from the service port.
  • Store can in a cool, dry place or discard according to state or local guidelines.
  • BONUS: Recharge hose can be detached and SMART CLIPS reinserted into cap for reuse.

DANGER: STORE IN COOL PLACE – NEVER IN PASSENGER CABIN OF VEHICLE AS CAN MAY EXPLODE. DO NOT EXPOSE TO TEMPERATURES ABOVE 120°F. DO NOT PUNCTURE OR INCINERATE.

WARNING: KEEP OUT OF REACH OF CHILDREN. EXPOSURE TO SKIN MAY CAUSE FROSTBITE. FLUSH WITH WARM WATER. IF SPRAYED INTO EYES, FLUSH WITH WARM WATER. IF INHALED, REMOVE TO FRESH AIR AND CALL PHYSICIAN IMMEDIATELY. CONTAINS 2,3,3,3 TETRAFLUOROPROP-1-ENE (CAS # 754-12-1).

WARNING: This Product can expose you to chemicals including lead, cadmium, and DBP which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov

Menu